1989 Ford F150 Fuel Tank Selector Valve Diagram – This blog post will provide a 1989 Ford F150 fuel tank selector valve diagram. The fuel tank selector valve is responsible for sending the correct fuel mixture to the engine, depending on its position. There are three positions: off, on, and reserve. If your truck isn’t starting or running right, it might be time to check the selector valve. Let’s take a look at the diagram below!
Contents
Where Is The Fuel Tank Selector Valve On 1990 F150?
On a 1990 Ford F150, the fuel tank selector valve is located on the frame rail between the tanks and the filter. This is where you will switch which tank the fuel is being drawn from. The switch is most likely labeled “Left” and “Right.” Make sure your truck is turned off and has had time to cool down before you attempt to locate or change the position of the valve.
If you need to change the position of the valve, use a Phillips head screwdriver to loosen the screws that hold it in place. Once you have loosened the screws, carefully turn the valve to the position, you want it in. For example, if you want to draw fuel from the left tank, turn the valve to the left. If you want to draw fuel from the right tank, turn the valve to the right. Once you have turned the valve to the correct position, tighten the screws back in place. You should now be able to start your truck and drive normally.
Where Is The Fuel Selector Valve?
The fuel selector valve is an important component of any vehicle with more than one fuel tank. Its primary purpose is to allow the driver to choose which tank the engine will draw fuel from. This is important because, in some cases, one tank may contain a different type of fuel than the other, or one tank may be empty while the other still has plenty of fuel. The selector valve also plays a role in preventing fuel cross-contamination.
Only allowing fuel to flow from one tank at a time minimizes the risk of mixing different types of fuel, which can cause engine problems. The exact location of the selector valve varies depending on the vehicle, but it is typically located between the fuel pump and the fuel tanks. In some cases, it may be located on the side of the vehicle near the fuel tanks.
For vehicles with in-tank fuel pumps or pumps located between the tanks and valve, a different type of valve is used. If you are unsure about the location of your vehicle’s selector valve, consult your owner’s manual or a qualified mechanic.
How Does A Fuel Selector Valve Work?
The fuel selector valve is an important component of any vehicle with more than one fuel tank. As the name implies, the selector valve allows the driver to choose which tank will be used to power the engine. The valve is linked to a switch that is typically located near the passenger seat, and this switch sends a signal to the valve that determines whether it should be open or closed.
When the switch is in the “on” position, it sends a signal to the valve that closes the connection to the selected fuel tank and opens the connection to the other tank. This ensures that only the desired fuel is used and that no accident mixing of different fuel types occurs. The fuel selector valve is a simple but crucial component of any vehicle with more than one fuel tank, and it ensures that the engine always has a steady supply of the correct type of fuel.
Where Is The Inertia Switch On A 1989 F150?
On my 89 F150 5.0 XLT 2WD extended cab, the “inertia switch” or fuel pump shut-off switch is down by the driver’s left foot where the wire harness runs out through the firewall. There are two relays in the under-hood relay box; the fuel pump relay is the one closest to the fender. The inertia switch is a simple device that cuts off power to the fuel pump in case of a collision. It’s there to prevent fuel spills and fires in case of an accident.
The switch is usually mounted on or near the fuel tank, and it’s connected to a wire that runs to the fuel pump. When the switch is tripped, it cuts off power to the fuel pump, stopping fuel flow. The inertia switch is designed to be triggered by a sudden deceleration, which might occur in a collision.
However, the switch can also be tripped by a sudden jolt, which might occur if you hit a large pothole. If your truck suddenly stalls and won’t start, check if the inertia switch has been tripped. If it has, reset it by pushing the button. The button is usually red, and it will pop out when the switch is tripped. Once you’ve reset the switch, try starting your truck again.
Where Is The Fuel Pump Reset Button Located?
If your vehicle has been in a collision, the fuel pump shut-off switch may have been activated. This is a safety feature designed to prevent the engine from starting if there is damage to the fuel system. To reset the switch, you will need to locate the access panel on the right side of the luggage compartment.
Once you have found the panel, you will see a red reset button on top of the switch. Pressing this button will reset the switch and allow the engine to start. If you have any trouble locating the fuel pump shut-off switch, consult your owner’s manual or contact a qualified technician for assistance.
Final Words
The fuel tank selector valve diagram provides a detailed look at how the fuel system works in your Ford F150. If you are experiencing problems with your truck’s fuel system, this diagram can help you troubleshoot and fix the issue.
