Viper Alarm Key Fob Not Working

Viper Alarm Key Fob Not Working

Are you having trouble Viper Alarm Key Fob Not Working? If so, don’t worry – you’re not alone. This blog post will explain what to do if your key fob isn’t working properly. We’ll also provide tips for keeping your key fob in good condition. So whether you’re a new Viper owner or just need a refresher course, keep reading for helpful information on your key fob!

Why Is My Viper Key Fob Not Working?

If your Viper key fob isn’t working, there are a few things you can check. First, make sure the batteries are fresh. If they’re not, replace them and see if that solves the problem. If the key fob still doesn’t work, it’s possible that the signal is being blocked.

Metal objects, electronic devices, and even your body can interfere with the signal. Try moving the key fob closer to the receiver or removing any objects that might be blocking the signal. If none of these solutions work, you may need to contact a Viper dealer or locksmith for assistance.

How Do I Re-sync My Viper Key Fob?

The Viper key fob is an important part of the Viper security system. If the key fob becomes out of sync with the system, it will need to be re-synced. To do this, simply follow these steps:

  1. Press and hold the “Valet” button on the key fob for six seconds. The “Valet” button is located on the side of the key fob.
  2. Turn the ignition on and off three times within five seconds.
  3. The key fob is now re-synced and ready to be used.

Tips for Keeping Your Viper Key Fob in Good Condition

You can do a few things to keep your Viper key fob working properly. First, avoid exposing it to extreme temperatures. If it’s too hot or cold outside, leave the key fob inside, where it will be more comfortable. Second, don’t store the key fob near electronic devices. The signal from these devices can interfere with the key fob’s signal. Finally, be careful not to drop or otherwise damage the key fob. A damaged key fob may not work properly or could even break completely.

Your Viper key fob should give you years of trouble-free use if you follow these tips. But if you do have problems with your key fob, don’t hesitate to contact a Viper dealer or locksmith for assistance.

How Do I Reset My Viper Remote?

If you need to reset your Viper remote, there are only a few steps you need to follow. First, locate the small black button on the back of the remote once you’ve found it, press and hold the button for at least five seconds. After that, release the button and press it again for three seconds.

Finally, press and hold the button for one second. This will reset your remote and should return it to its default settings. If you have any further questions or problems, consult your Viper manual or contact customer service for assistance.

How Do I Get My Viper Out Of Valet Mode?

Depending on which model you have, there are a few different ways to get your Viper out of valet mode. For most models, you’ll need the remote control and the four-digit PIN assigned to the car when it was first put into valet mode.

Once you have the remote and PIN, you can simply enter them into the car’s system to disable valet mode. However, some newer models may require you to hold down a specific button on the remote for a few seconds before entering the PIN. Consult your Viper’s manual for more specific instructions if you’re still having trouble.

What does the F mean on Viper remote?

The F on a Viper remote indicates the device is set to factory default settings. To return the remote to these settings, press and hold the Star (*) and Enter buttons simultaneously for three seconds. The default setting for most Viper remotes is Channel 1, with a CTCSS/PL tone of 67.7 Hz.

This can be changed by pressing the Menu button and using the arrow keys to navigate through the menu options. The F on a Viper remote also indicates that the battery is low and needs to be replaced. To replace the battery, remove the back cover of the remote and insert a new CR2032 lithium coin cell battery.

Make sure the positive side of the battery is facing up before replacing the back cover once the new battery is in place, press and holds the Star (*) and Enter buttons simultaneously for three seconds to exit the menu and return to normal operation.

Viper 7656V 1-Way Remote Replacement 5-button remote control for select Viper security and remote start systems at Crutchfield

What does the AUX button do on the Viper remote?

The AUX button on the Viper remote is used to control various features on your car. It can turn on the headlights, control the interior lights, or even open the trunk. The AUX button can also lock or unlock the doors or turn on the windshield wipers.

In addition, the AUX button can be used to activate the panic alarm. This feature is particularly useful if you are in an accident or if your car has been stolen. By pressing the AUX button, you can instantly activate the alarm, notify the authorities, and help track down your vehicle.

Final Verdict

Thank you for reading our blog post about the Viper alarm key fob not working. We hope that our tips have been helpful. If you are experiencing any other issues with your Viper alarm, please do not hesitate to reach out to us for assistance. We would be happy to help! Have a great day

Leave a Comment

Your email address will not be published. Required fields are marked *